Support for P4P V2.0

The P4P V2.0’s camera is the same as the P4P’s. It is equipped with a 1-inch 20-megapixel sensor,supporting shooting 4096x2160 videos at 60 fps (H.264) or 30 fps (H.265) with a maximum bitrate of 100 Mbps. It also has a manually adjustable aperture from F2.8 to F11. Auto, M, A (aperture priority), and S (shutter priority) modes are available. For more details, please refer to the Specifications on the product page on DJI’s official website.

Yes.

In S-mode, the aircraft can tilt up to 42 degrees, while the gimbal can move at most 45 degrees upward and 120 degrees downward. Hence, the gimbal cannot point forward horizontally when the aircraft is flying quickly in S-mode. To solve such issue, move the pitch of the gimbal downward by at least 12 degrees when flying in S-mode.

100 Mbps.

Their remote controllers are different.
The P4P+ V2.0’s remote controller includes a 5.5-inch, 1080p, 1000 nit built-in display. Its screen can be seen clearly in direct sunlight. It can be used in low-temperature environments, and a mobile device is no longer required. The remote controller also features an HDMI port, a micro-SD card slot, a built-in microphone, and a speaker, which allows for live streaming and video editing anytime, anywhere.

No, as their image transmission technologies are different.

A. The color of the DJI logo on the top of the P4P’s remote controller is silver, while that of the P4P V2.0 is gold.
B. Heat dissipation holes are added to the bottom of the P4P V2.0’s remote controller.

The P4P V2.0’s remote controller uses a new OcuSync transmission technology, which allows a wireless connection to DJI Goggles RE.

No.

Users cannot switch between FCC and CE manually. The remote controller will enable FCC or CE mode based on your location in accordance with local laws and regulations.

A.Using DJI GO 4: Tap “Link Remote Controller” under Remote Controller Settings. The remote controller’s Status LED will blink blue, and you will hear a “DDD…” alarm. Then press the drone’s Link Button with a proper tool to link your remote controller to the P4P V2.0.
B.Using a Button Combination: Press the C1, C2 and video recording buttons at the same time. After the remote controller’s Status LED blinks blue, and you hear a “DDD…” alarm, press the drone’s Link Button with a proper tool to link your remote controller to the P4P V2.0.

The P4P V2.0 is powered by a new OcuSync transmission system, and it supports 2.4 GHz and 5.8 GHz frequency bands.

FCC: 10 km, CE: 6 km (Unobstructed, free of interference).
Actual transmission distance varies depending environmental conditions and operation.(2.4GHz)

Smooth Mode: 720p 60 fps
Normal Mode: 720p 30 fps
HD Mode: 1080p 30 fps
It can be set under the Image Transmission Settings in DJI GO 4.

The remote controller’s signal will be affected if its antennas are not positioned properly. Try to adjust the antennas.

5870 mAh, 15.2 V, 89.8 Wh.

Around 90 minutes.

Keep the Intelligent Flight Battery away from water or moisture. Battery level should fall between 45% and 65% when the Intelligent Flight Battery is to be stored for a long period. If the Intelligent Flight Battery is to be stored for more than three months, it should be fully charged and discharged once every three months to avoid over-discharging.

Yes, when the voltage of the battery cells is lower than 3.62 V, the display will turn yellow.

Battery capacity will decrease significantly when the Intelligent Flight Battery is used at low temperatures (below minus 10 degree Celsius). It is recommended to warm up the Intelligent Flight Battery to 20 degrees Celsius before a flight.

When the battery has been stored for a long period with over 65% charge, the auto-discharging function will be triggered. The Intelligent Flight Battery will discharge to 65% of its total power automatically while emitting moderate heat.

The Phantom 4 Pro V2.0’s firmware can be updated with both DJI GO 4 and DJI Assistant 2. But the update methods differ.
If updating with DJI GO 4, the mobile device and drone do not need to be connected to the USB OTG cable and micro USB cable anymore. Instead, the remote controller’s firmware and aircraft’s firmware can be updated in the app at the same time.
When updating with DJI Assistant 2, you can choose to update the remote controller’s firmware or aircraft’s firmware separately or update both of them at the same time.

The left and right infrared sensors will only function in Beginner Mode and Tripod Mode.

DJI GO 4 can run on both iOS and Android mobile devices. For more details, please see the Specifications on the product page on DJI’s official website.

0.2 meters to 7 meters.

Yes.